Insteon SwitchLinc Relay (2476S) Manual Manual do Utilizador Página 15
- Página / 21
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Page 15 of 21 Rev: 1/21/2014 7:15 AM
Change Paddle and LED Colors
You can swap out the included white LEDs and/or front paddle and trim frame assembly with a color-
change kit before or after SwitchLinc is installed. During the changeover process, power and load may
remain on and operating. There are no dangerous voltages or unsafe areas under the paddle.
• LED kits available: frosted white, four color (includes red, amber, green and blue)
• Paddle kits available: almond, light almond, ivory, gray, black, brown, white
1) If SwitchLinc is already installed in the wall, remove the
wallplate from the switch wall box
2) Remove the four Phillips screws that hold the paddle
assembly to the metal frame
3) Pull the entire paddle straight away from the switch. You may
have to wiggle the bottom of the frame to get it free from the
Set button
Figure 1: Paddle assembly and SwitchLinc
body separated
4) Using a flat blade or needlenose pliers, snap the large light
pipe out of the frame (as shown in Figure 2 at right). Do the
same for the small light pipe
Figure 2: Snap out the light pipes with a
flat tool.
5) Choose which LEDs and/or paddle and trim frame you would like to install into SwitchLinc
6) Orient the new small light pipe with its protrusion facing
toward center of the new frame. Snap it into place. If placed
in backwards or reverse, it will not click into place. (Refer to
Figure 3 at right.)
7) Orient the new large light pipe with side that has the most
protrusions facing toward the center of the new frame. Using
only finger pressure, snap the light pipe into the frame.
(Refer to Figure 3 at right).
Figure 3: Insert the new light pipes with the
protrusions facing the center
8) If both light pipes are installed correctly, they will stick straight out from the back of the frame
(as shown in Figure 4, below left). If installed incorrectly, they will appear to be tilted (as shown
- SwitchLinc™ Dimmer 1
- Features 3
- Installing SwitchLinc 4
- Using SwitchLinc 9
- Ramp Rate 10
- Make SwitchLinc a Controller 11
- Make SwitchLinc a Responder 11
- Power Restore 12
- Add an X10 Address 12
- Remove an X10 Address 12
- Advanced Features 13
- Factory Reset 14
- Change LED Brightness Levels 14
- Specifications 16
- Troubleshooting 18
- Certification and Warranty 21
Manuais e produtos relacionados com Hardware Insteon SwitchLinc Relay (2476S) Manual
Hardware Insteon SwitchLinc Dimmer (Dual-Band) - (2477D) Manual (Ve Manual do Utilizador
(16 páginas)
(16 páginas)
Hardware Insteon SwitchLinc 2-Wire Dimmer (RF) (2474DWH) Quick Star Manual do Utilizador
(1 páginas)
(1 páginas)
Hardware Insteon SwitchLinc Dimmer, High Wattage (Dual-Band) (2477D Manual do Utilizador
(15 páginas)
(15 páginas)
Hardware Insteon SwitchLinc Dimmer 100-277VAC (dual band) (2478D) Q Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Insteon SwitchLinc Dimmer 100-277VAC (dual band) (2478D) M Manual do Utilizador
(19 páginas)
(19 páginas)
Hardware Insteon KeypadLinc Dimmer, 6 button (2486DWH6) Quick Start Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Insteon KeypadLinc Dimmer, 8 button (2486DWH8) Quick Start Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Insteon Keypad Dimmer (Dual-Band) (2334-2xx US) Quick Star Manual do Utilizador
(2 páginas)
(2 páginas)
(3 páginas)Orion Car Audio HCCA COMPETITION HCCA154 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Autolautsprecher Orion Car Audio HCCA COMPETITION HCCA154.
Wir stellen 1 PDF-Handbücher Orion Car Audio HCCA COMPETITION HCCA154 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentários a estes Manuais